Structure of turbulent rich hydrogen‐air premixed flames

In the present article, series of experiments were conducted to study the structure characteristics of premixed flames in turbulent rich hydrogen‐air mixtures within a constant‐volume turbulent combustion system, 7 equivalence ratios (1.2, 1.4, 1.6, 1.8, 2.0, 2.2, and 2.5), and 5 turbulent intensity (0, 0.494, 0.742, 1.080, and 1.309 m/s) were studied. With the increase of turbulent intensity, the cellularity degree was obviously enhanced for turbulence promoted the formation and the development of initial cracks by wrinkling flame‐front; furthermore, the enhanced hydrodynamic instability was also one important reason. Turbulence would change the linear growth of critical radius to equivalence ratio into nonlinear, but the variation extents had limitation. The wrinkling index of flame‐front would rise as flame expanded, and the wrinkling index on flames with similar size would be increased with the increase of turbulence once the turbulent intensity was sufficiently high. From the variations of the root mean square of related oscillation on flame‐front, it could be found that the partial amount of oscillation induced by sole turbulence was declined as flame expanded for the breakup of large eddies.     

制备工艺对聚氨酯酰亚胺泡沫性能的影响

以均苯四甲酸二酐(PMDA)、多苯基多亚甲基多异氰酸酯(PAPI)、聚醚多元醇为主要原料,分别采用聚酰亚胺(PI)预聚法、聚氨酯(PU)预聚法和一步法制备聚氨酯酰亚胺泡沫,从微观形貌、力学性能、热稳定性能以及阻燃性能方面对上述3种制备工艺进行对比和评估。实验结果表明,采用一步法制备PUI泡沫时,PU链段和PI链段同时增长,容易造成泡孔缺陷,导致泡沫的力学性能较差;在采用PU预聚法制备的PUI泡沫中,PU链段含量较高,因此,泡孔孔径分布较宽且平均泡孔直径较大,对应的热稳定性和阻燃性能较差;采用PI预聚法制备的PUI泡沫的泡孔孔径分布窄且平均泡孔直径较小,对应的压缩性能、热稳定性以及阻燃性能均达到最佳。     

超声协助蒙脱土分散于聚磷酸铵阻燃聚丙烯的研究

阻燃剂能够增强聚丙烯（PP）的阻燃性能,但也会降低其力学性能,因此对阻燃剂进行改性以改善聚丙烯的力学性能显得至关重要。以传统的膨胀型阻燃剂（IFR）[由聚磷酸铵（APP）、季戊四醇（PER）、三聚氰胺（MA）组成]为PP阻燃。在合成APP过程中引入有机蒙脱土（OMt）。APP围绕OMt形成,剥离OMt使其能够较好地分散在阻燃剂中。为使OMt更好地分散在阻燃剂中,在磷酸氢二铵（DAP）、尿素（UREA）溶液中加入OMt,之后对溶液进行超声处理,蒸干后形成DAP-UREA-OMt与五氧化二磷反应生成APP。在PP中添加改性阻燃剂,有助于PP材料阻燃性能的提升与减缓力学性能的下降。当阻燃剂添加量为30%（阻燃剂添加量占总质量的质量分数）时,PP/IFR_APP/OMt复合材料的氧指数达到29.8%,通过V-0测试,拉伸强度为22.0 MPa,高出传统方法0.7 MPa。     

亚磷酸酯功能化聚硅氧烷扩链聚乳酸的阻燃性能研究

将聚氨基环氧基硅氧烷（PSQ）以及亚磷酸酯功能化的聚氨基环氧基硅氧烷（PPSQ）与聚乳酸（PLA）通过熔融共混制备了扩链PLA。研究了亚磷酸酯基团的引入对PSQ在PLA中的扩链和阻燃性能的影响，探究PPSQ在PLA中的阻燃机理。结果表明，相比于PSQ，PPSQ可以明显提高PLA的分子量和复合黏度，具有更好的扩链作用；PPSQ的引入可以明显改善PLA的阻燃性能，使得PLA?PPSQ的极限氧指数提高至25.4 %，比纯PLA提升了31.6 %，且使得PLA的热释放速率峰值和总热释放量分别下降了18.1 %和16.6 %。分析可知，由于亚磷酸酯基团的引入，促使PLA?PPSQ中的硅元素在燃烧过程中向炭层表面迁移形成更多富含碳化硅和氧化硅的致密炭层，起到隔热隔氧的作用，进而发挥优异的阻燃性能。     

Reduction of chlorophenols and sludge management from paper industry wastewater using electrocoagulation process

ABSTRACT

In this study, electrocoagulation (EC) was used to determine the optimum conditions on the basis of maximum chemical oxygen demand (COD) and color removal. At the optimum conditions chlorophenols (CPs), biological oxygen demand and total organic carbon (TOC) were determined. The biodegradability of wastewater was increased significantly with 63% COD, 98% color, 61% TOC and overall 65.51% reductions in CPs. Further, the electro-coagulated sludge was characterized by using different analytical techniques to assist the physicochemical and elemental phases, to find-out better management option, reusability for plant growth and safe disposal. Additionally, aluminum content (70.62%) was successfully recovered from sludge.     

基于环三磷腈磷氮阻燃剂的合成及其在聚氨酯泡沫的应用

以六氯环三磷腈、对羟基苯甲醛、苯胺及亚磷酸二乙酯等原料，成功合成阻燃剂六（4-苯胺基次甲基苯氧基-亚磷酸二乙酯基）环三磷腈（HADPPCP），用于阻燃基于苹果酸多元醇的聚氨酯硬泡。HADPPCP具有良好的热稳定性和成炭性，氮气气氛下的初始分解温度为191.9℃，700℃时的残炭量高到46.8%（质量）。HADPPCP的加入可以改善聚氨酯硬泡的热稳定性、阻燃性能和燃烧行为。添加25%(质量)的HADPPCP可以将聚氨酯泡沫的氧指数从18%提高到25%，最大热释放速率和总热释放量分别从230 kW/m²和20.1 MJ/m²降低至213 kW/m²和16.6 MJ/m²，总产烟量从10.5 m²下降到5.3 m²。     

Synergistic fire-retardancy properties of melamine coated ammonium poly(phosphate) in combination with rod-like mineral filler attapulgite for polymer-modified bitumen roofing membranes

A novel intumescent (carbonization, acid donor and foaming) fire retardant that mimics carbon nanotubes was introduced into bitumen roofing and characterized using cone calorimetry as the main analytical tool. The experimental results indicate that 18% (by mass) attapulgite mineral (ATTP) mixed with base bitumen decreased the peak heat release rate per unit area (pHRRPUA) by 10%. Further, incorporation of melamine coated ammonium polyphosphate (MAPP) decreased the pHRRPUA by 52% and a mixture of these (3:1, ATTP:MAPP) decreased the pHRRPUA by 25% as compared to adding CaCO₃ as a filler. The residual mass loss after the cone test was also improved with up to 3%. The indication of a positive synergistic flame retardant effect of the ATTP-MAPP mixture is supported by thermogravimetric analysis. The addition of this rod-like mineral improved the general fire retardant properties of the base bitumen and increased the viscosity. Therefore, the polymer-modified bitumen with both fire retardant and rheological properties (providing mechanical strength) is a promising novel approach in the design of bitumen roofing membranes.     

线性富磷化阻燃剂在聚氨酯泡沫中的应用研究

通过界面聚合法合成了一种线性富磷化阻燃剂（LPRFR），将LPRFR与可膨胀石墨（EG）复配制备了阻燃聚氨酯泡沫（RPUF），使用红外光谱分析仪、核磁共振分析仪对阻燃剂LPRFR的化学结构进行了表征，并通过极限氧指数仪、锥形量热仪、扫描电子显微镜和红外光谱分析仪对RPUF的燃烧性能、微观形貌和化学结构进行了分析。结果表明，仅10 %（质量分数，下同）的LPRFR 与8 %EG复配后，RPUF的极限氧指数（LOI）便达到26.1 %；LPRFR和EG能大幅降低RPUF的热释放速率，并提高基体的成炭能力； LPRFR参与了燃烧过程中的成炭反应，形成了含P—O—C及P=O结构的高质量炭层，有效隔绝了氧气和热量；LPRFR是一种对于聚氨酯泡沫阻燃性能优异的新型阻燃剂。     

Investigation of the thermal behavior effect of the surrounding material environment on the swirling flame structure

This paper is focusing on the numerical simulation of a swirling flame, resulting from the interaction of multiple fires, evolving in a free and unlimited environment. A typical system, formed by a central fire source surrounded by four heat sources, is used. Since the thermal characteristic of the surrounding sources is the main engine for the rotation of flame, a detailed study is performed by varying the heating flux of these sources. This study shows that an increase of the heating flux of surrounding sources has as a result an intensification of the penetrating air puffs through the openings between the surrounding four heat sources. These puffs tangentially drive the central flame, thus producing a marked improvement on the angular momentum. Moreover, this study shows that the flame height is strongly affected by the flame rotation. Moreover, two different aspects of the flame height evolution are observed from the flow visualization and the thermal and dynamic fields for the different cases studied.     

Maximum temperature rise of fire plume ejected out of the compartment window with a horizontal eave

This study focuses on the maximum temperature rise of fire plume ejected out of the compartment window with a horizontal eave. Based on the symmetry of ejected plume and pictures recorded by the cameras in the study, the shape of ejected thermal plume out of the window under the eave is suggest as an isosceles trapezoid, and the ejected thermal plume rising at the edge of the eave is assumed to be a rectangular fire source. The dimensions of the rectangular fire source are theoretically deduced for compartment fire process of different window geometry, width of eave, and heat release rate, according to the conservation of plume mass. The previous predictive model for plume temperature proposed by Quintiere is popularized to the ejected flame above an eave by including the dimensions of the rectangular fire source as well as the width of eave. The results would provide theoretical guidance to the application of fireproof eave in high-rise building for fire protection designs.